Coarse dirt filter basket

Rubber lip seal for inserting DN pipes into a tank or cistern. Pipe Bore Part No. DN 32 Ø 37 mm G0002440 DN 40 Ø 46 mm G0002500 DN 50 Ø 57 mm G0000713 DN 70 Ø 85 mm G0000715 DN 100 Ø 125 mm G0000717 DN 150 Ø 174 mm G0001437 DN 200 Ø 215 mm G0001788 DN 250 Ø 265 mm G0002961 DN 300 Ø 335 mm G0002962

GreenLife's gutter guard is the perfect filter for rainwater. Whether the water is collected in cisterns or rain barrels, plant debris such as leaves and twigs can reduce water quality. It is therefore always recommended to pre-filter rainwater as thoroughly as possible, starting right at the gutter. Leaf guards filter rainwater Especially in the fall, when trees shed their leaves, it can be very frustrating when heavy rain causes leaves to enter the downspout and thus the rainwater tank. Not only does the quality of the collected water suffer from the debris, but it can also quickly clog the downspout. Cleaning often involves a lot of effort. Therefore, always use a leaf guard. Potential problems without a leaf guard Clogged downspouts Blockages in water hoses or showerheads Discoloration of the water Reduced water quality Staining of the gutter Breeding ground for pests With this simple leaf guard from GreenLife, such problems are a thing of the past. Assembly is incredibly easy, and cleaning usually requires nothing more than a hand brush. The gutter guard also provides reliable protection against birds. They can no longer nest in the gutter and must find other places to settle. Can I filter the rainwater even further? Yes, because the gutter guard is only a pre-filter. Depending on the type of your rainwater harvesting system, you can also use downspout filters, built-in filters, or tank-mounted filters. In addition to these mechanical filters, the patented Biovitoren for cisterns can also be used. These are biological filters that require very little maintenance. Installation of the gutter protection grid Installing the gutter guard is very straightforward. Each package contains segments for approximately 3.00 meters, which simply slot together. Depending on the width of the gutter, the guard can be folded. It fits any standard gutter size.https://www.youtube.com/watch?v=IVG8j1yDEMM

GreenLife's gutter guard is the perfect filter for rainwater. Whether the water is collected in cisterns or rain barrels, plant debris such as leaves and twigs can reduce water quality. It is therefore always recommended to pre-filter rainwater as thoroughly as possible, starting right at the gutter. Leaf guards filter rainwater Especially in the fall, when trees shed their leaves, it can be very frustrating when heavy rain causes leaves to enter the downspout and thus the rainwater tank. Not only does the quality of the collected water suffer from the debris, but it can also quickly clog the downspout. Cleaning often involves a lot of effort. Therefore, always use a leaf guard. Potential problems without a leaf guard Clogged downspouts Blockages in water hoses or showerheads Discoloration of the water Reduced water quality Staining of the gutter Breeding ground for pests With this simple leaf guard from GreenLife, such problems are a thing of the past. Assembly is incredibly easy, and cleaning usually requires nothing more than a hand brush. The gutter guard also provides reliable protection against birds. They can no longer nest in the gutter and must find other places to settle. Can I filter the rainwater even further? Yes, because the gutter guard is only a pre-filter. Depending on the type of your rainwater harvesting system, you can also use downspout filters, built-in filters, or tank-mounted filters. In addition to these mechanical filters, the patented Biovitoren for cisterns can also be used. These are biological filters that require very little maintenance. Installation of the gutter protection grid Installing the gutter guard is very straightforward. Each package contains segments for approximately 3.00 meters, which simply slot together. Depending on the width of the gutter, the guard can be folded. It fits any standard gutter size.https://www.youtube.com/watch?v=IVG8j1yDEMM

GreenLife's gutter guard is the perfect filter for rainwater. Whether the water is collected in cisterns or rain barrels, plant debris such as leaves and twigs can reduce water quality. It is therefore always recommended to pre-filter rainwater as thoroughly as possible, starting right at the gutter. Leaf guards filter rainwater Especially in the fall, when trees shed their leaves, it can be very frustrating when heavy rain causes leaves to enter the downspout and thus the rainwater tank. Not only does the quality of the collected water suffer from the debris, but it can also quickly clog the downspout. Cleaning often involves a lot of effort. Therefore, always use a leaf guard. Potential problems without a leaf guard Clogged downspouts Blockages in water hoses or showerheads Discoloration of the water Reduced water quality Staining of the gutter Breeding ground for pests With this simple leaf guard from GreenLife, such problems are a thing of the past. Assembly is incredibly easy, and cleaning usually requires nothing more than a hand brush. The gutter guard also provides reliable protection against birds. They can no longer nest in the gutter and must find other places to settle. Can I filter the rainwater even further? Yes, because the gutter guard is only a pre-filter. Depending on the type of your rainwater harvesting system, you can also use downspout filters, built-in filters, or tank-mounted filters. In addition to these mechanical filters, the patented Biovitoren for cisterns can also be used. These are biological filters that require very little maintenance. Installation of the gutter protection grid Installing the gutter guard is very straightforward. Each package contains segments for approximately 3.00 meters, which simply slot together. Depending on the width of the gutter, the guard can be folded. It fits any standard gutter size.https://www.youtube.com/watch?v=IVG8j1yDEMM

Biological Filter for Rainwater Harvesting Are you looking for a low-maintenance rainwater filter that purifies your water without chemicals and achieves a high yield of top-quality rainwater? Then you’re in good hands with the GreenLife Biovitor. The Biovitor contains no wear parts, so you can rely on maintenance intervals of up to ten years. We developed the GreenLife Biovitor to eliminate the need for chemical additives and high-maintenance filters in rainwater purification. Unlike conventional designs, the Biovitor uses the same natural processes for biological self-purification as our local water bodies. This ensures consistently high-quality rainwater in your rainwater harvesting system.How our patented BIOVITOR biological rainwater filter works The Biovitor purifies your rainwater 100% chemical-free based on the natural decomposition process of organic material, such as leaf debris. It consists of two optimally sized chambers that guarantee highly efficient biological processes. Here’s how it works: Rainwater flows through the gutter grate (or other leaf guards) into the gutter and finally through the downspout into the Biovitor, which is located in the tank or cistern. The first chamber contains marble gravel, which can slightly raise the pH of the water to neutralize slightly acidic rain, if necessary. This also slightly mineralizes the rainwater.From here, the pre-treated water flows into the second chamber, which is equipped with bio-active media. Here, the remaining organic components are decomposed and broken down in the water using oxygen and natural microorganisms. Inorganic components settle at the bottom. The clear and clean water then slowly enters the rainwater tank to avoid creating turbulence. The Biovitor acts as an inlet stabilizer and achieves 100% rainwater yield, as there are no losses due to contaminated rainwater filters.Applications for the BIOVITOR Rainwater Filter Our biological rainwater filter improves the quality of your rainwater through biological processes. It is suitable for all cisterns and can be retrofitted to almost all rainwater systems. Additionally, the Biovitor is very well suited for a rainwater system with subsequent infiltration; an additional filter before infiltration is then not necessary. Connection options: DN 100 (da = 110)  Connectable area: 170 m² Scope of delivery GreenLife BIOVITOR DN 100 Biological sedimentation filter with DN 100 connection (da = 110):Rainwater inlet (inlet pipe DN 100)Biovitor tank with 1st and 2nd Biovitor chambers and overflows into the tankMarble gravelBio-active mediaNOT included in the scope of delivery are the KG branch pipe DN110 and the KG elbow DN110 45°Maintenance and cleaning Since maintenance-intensive filter designs and chemical additives are not used and there are no wear parts, maintenance intervals are generally five to ten years. Cleaning of the pre-filter systems, e.g., gutter grates or other leaf separator technology, is essential and must be performed regularly.Additional Notes  Please refer to the operating instructions for installation, maintenance, and mounting of the Biovitor.

Biological Filter for Rainwater Harvesting Are you looking for a low-maintenance rainwater filter that purifies your water without chemicals and achieves a high yield of top-quality rainwater? Then you’re in good hands with the GreenLife Biovitor. The Biovitor contains no wear parts, so you can count on maintenance intervals of up to ten years. We developed the GreenLife Biovitor to eliminate the need for chemical additives and high-maintenance filters in rainwater purification. Unlike conventional designs, the Biovitor uses the same natural processes for biological self-purification as our local water bodies. This ensures consistently high-quality rainwater in your rainwater harvesting system. How our patented BIOVITOR biological rainwater filter works The Biovitor purifies your rainwater 100% chemical-free based on the natural decomposition process of organic material, such as leaf debris. It consists of two optimally sized chambers that guarantee highly efficient biological processes. Here’s how it works: Rainwater flows through the gutter grate (or other leaf guards) into the gutter and finally through the downspout into the Biovitor, which is located in the tank or cistern. The first chamber contains marble gravel, which can slightly raise the pH of the water to neutralize slightly acidic rain, if necessary. This also slightly mineralizes the rainwater. From here, the pre-treated water flows into the second chamber, which is equipped with bio-active media. Here, the remaining organic components are decomposed and broken down by oxygen and natural microorganisms in the water. Inorganic components settle at the bottom. The clear and clean water then slowly enters the rainwater tank to avoid creating turbulence. The Biovitor acts as an inlet stabilizer and achieves 100% rainwater yield, as there are no losses due to contaminated rainwater filters. Applications for the BIOVITOR Rainwater Filter  Our biological rainwater filter improves the quality of your rainwater through biological processes. It is suitable for all cisterns and can be retrofitted to almost all rainwater systems. Additionally, the Biovitor is highly suitable for a rainwater system with subsequent infiltration; an additional filter before infiltration is then not necessary.  Connection options: DN 300 (dₐ = 315)  Connectable area: 3250 m² Scope of delivery GreenLife BIOVITOR DN 300 Biological sedimentation filter with DN 300 connection (dₐ = 315):Rainwater inlet (inlet pipe DN 300)Biovitor tank with 1st and 2nd Biovitor chambers and overflows into the tankMarble gravelBio-active mediaMaintenance and Cleaning Since the system does not rely on high-maintenance filter designs or chemical additives and contains no wear parts, maintenance intervals are typically five to ten years. Cleaning of pre-filter systems, e.g., gutter screens or other leaf-trapping devices, is essential and must be performed regularly.Additional notes Please refer to the operating instructions for installation, maintenance, and mounting of the Biovitor.

Biological Filter for Rainwater Harvesting Are you looking for a low-maintenance rainwater filter that purifies your water without chemicals and achieves a high yield of top-quality rainwater? Then you’re in good hands with the GreenLife Biovitor. The Biovitor contains no wear parts, so you can rely on maintenance intervals of up to ten years. We developed the GreenLife Biovitor to eliminate the need for chemical additives and high-maintenance filters in rainwater purification. Unlike conventional designs, the Biovitor uses the same natural processes for biological self-purification as our local waterways. This ensures consistently high-quality rainwater in your rainwater harvesting system. How our patented BIOVITOR biological rainwater filter works The Biovitor purifies your rainwater 100% chemical-free based on the natural decomposition process of organic material, such as leaf debris. It consists of two optimally sized chambers that guarantee highly efficient biological processes. Here’s how it works: Rainwater flows through the gutter grate (or other leaf guards) into the gutter and finally through the downspout into the Biovitor, which is located in the tank or cistern. The first chamber contains marble gravel, which can slightly raise the pH of the water to neutralize slightly acidic rain, if necessary. This also slightly mineralizes the rainwater. From here, the pre-treated water flows into the second chamber, which is equipped with bio-active media. Here, the remaining organic components are decomposed and broken down by oxygen and natural microorganisms in the water. Inorganic components settle to the bottom. The clear and clean water then slowly enters the rainwater tank to prevent turbulence. The Biovitor acts as an inlet stabilizer and achieves 100% rainwater yield, as there are no losses due to contaminated rainwater filters.  Applications for the BIOVITOR Rainwater Filter  Our biological rainwater filter improves the quality of your rainwater through biological processes. It is suitable for all cisterns and can be retrofitted to almost all rainwater systems. Additionally, the Biovitor is very well suited for a rainwater system with subsequent infiltration; an additional filter before infiltration is then not necessary.  Connection options: DN 250 (dₐ = 250) Connectable area: 1,750 m² Scope of delivery GreenLife BIOVITOR DN 250 Biological sedimentation filter with DN 250 connection (dₐ = 250):Rainwater inlet (inlet pipe DN 250)Biovitor tank with 1st and 2nd Biovitor chambers and overflows into the tankMarble gravelBio-active mediaMaintenance and CleaningSince the system does not rely on maintenance-intensive filter designs or chemical additives and contains no wear parts, maintenance intervals are typically five to ten years. Cleaning of the pre-filter systems, e.g., gutter screens or other leaf-trapping devices, is essential and must be performed regularly.Additional notes  Please refer to the operating instructions for installation, maintenance, and mounting of the Biovitor. 

Biological Filter for Rainwater Harvesting Are you looking for a low-maintenance rainwater filter that purifies your water without chemicals and achieves a high yield of top-quality rainwater? Then you’re in good hands with the GreenLife Biovitor. The Biovitor contains no wear parts, so you can rely on maintenance intervals of up to ten years. We developed the GreenLife Biovitor to eliminate the need for chemical additives and high-maintenance filters in rainwater purification. Unlike conventional designs, the Biovitor uses the same natural processes for biological self-purification as our local water bodies. This ensures consistently high-quality rainwater in your rainwater harvesting system.How our patented BIOVITOR biological rainwater filter works The Biovitor purifies your rainwater 100% chemical-free based on the natural decomposition process of organic material, such as leaf debris. It consists of two optimally sized chambers that guarantee highly efficient biological processes. Here’s how it works: Rainwater flows through the gutter grate (or other leaf guards) into the gutter and finally through the downspout into the Biovitor, which is located in the tank or cistern. The first chamber contains marble gravel, which can slightly raise the pH of the water to neutralize slightly acidic rain, if necessary. This also slightly mineralizes the rainwater. From here, the pre-treated water flows into the second chamber, which is equipped with bio-active media. Here, the remaining organic components are decomposed and broken down by oxygen and natural microorganisms in the water. Inorganic components settle at the bottom. The clear and clean water then slowly enters the rainwater tank to prevent turbulence. The Biovitor acts as an inlet stabilizer and achieves 100% rainwater yield, as there are no losses due to contaminated rainwater filters.Applications for the BIOVITOR Rainwater Filter  Our biological rainwater filter improves the quality of your rainwater through biological processes. It is suitable for all cisterns and can be retrofitted to almost all rainwater systems. Additionally, the Biovitor is very well suited for a rainwater system with subsequent infiltration; an additional filter before infiltration is then not necessary.  Connection options: DN 200 (dₐ = 200) Connectable area: 1000 m²Scope of delivery GreenLife BIOVITOR DN 200 Biological sedimentation filter with DN 200 connection (dₐ = 200):Rainwater inlet (inlet pipe DN 200)Biovitor tank with 1st and 2nd Biovitor chambers and overflows into the tankMarble gravel Bio-active mediaMaintenance and Cleaning Since the system does not rely on high-maintenance filter designs or chemical additives and contains no wear parts, maintenance intervals are typically five to ten years. Cleaning of pre-filter systems, e.g., gutter screens or other leaf-trapping devices, is essential and must be performed regularly.Additional notes Please refer to the operating instructions for installation, maintenance, and mounting of the Biovitor. 

Biological Filter for Rainwater Harvesting Are you looking for a low-maintenance rainwater filter that purifies your water without chemicals and achieves a high yield of top-quality rainwater? Then you’re in good hands with the GreenLife Biovitor. The Biovitor contains no wear parts, so you can rely on maintenance intervals of up to ten years.We developed the GreenLife Biovitor to eliminate the need for chemical additives and high-maintenance filters in rainwater purification. Unlike conventional designs, the Biovitor uses the same natural processes for biological self-purification as our local water bodies. This ensures consistently high-quality rainwater in your rainwater harvesting system.  How our patented BIOVITOR biological rainwater filter works The Biovitor purifies your rainwater 100% chemical-free based on the natural decomposition process of organic material, such as leaf debris. It consists of two optimally sized chambers that guarantee highly efficient biological processes. Here’s how it works: Rainwater flows through the gutter grate (or other leaf guards) into the gutter and finally through the downspout into the Biovitor, which is located in the tank or cistern. The first chamber contains marble gravel, which can slightly raise the pH of the water to neutralize slightly acidic rain, if necessary. This also slightly mineralizes the rainwater. From here, the pre-treated water flows into the second chamber, which is equipped with bio-active media. Here, the remaining organic components are decomposed and broken down by oxygen and natural microorganisms in the water. Inorganic components settle at the bottom. The clear and clean water then slowly enters the rainwater tank to avoid creating turbulence. The Biovitor acts as an inlet stabilizer and achieves 100% rainwater yield, as there are no losses due to contaminated rainwater filters.Applications for the BIOVITOR Rainwater Filter  Our biological rainwater filter improves the quality of your rainwater through biological processes. It is suitable for all cisterns and can be retrofitted to almost all rainwater systems. Additionally, the Biovitor is very well suited for a rainwater system with subsequent infiltration; an additional filter before infiltration is then not necessary.  Connection options: DN 150 (dₐ= 160) Connectable area: 550 m² Scope of delivery GreenLife BIOVITOR DN 150 Biological sedimentation filter with DN 150 connection (dₐ = 160): Rainwater inlet (inlet pipe DN 150)Biovitor tank with 1st and 2nd Biovitor chambers and overflows into the tankMarble gravel Bio-active mediaMaintenance and Cleaning Since the system does not rely on high-maintenance filter designs or chemical additives and contains no wear parts, maintenance intervals are typically five to ten years. Cleaning of pre-filter systems, e.g., gutter screens or other leaf-trapping technology, is essential and must be performed regularly.Additional notes Please refer to the operating instructions for installation, maintenance, and mounting of the Biovitor.